Opens in a new tab

P&T Metals is a family-owned business located in Southern California, servicing businesses and industries for 58+ years.

October 10, 2026

How to Build a Scrap Credit Into a Demolition Bid

A demolition scrap salvage credit belongs in the bid, not in the surprise column at the end of the job. Most estimators know that. Fewer have a method for turning recovered metal into a number they’d defend in a scope meeting.

What is a salvage credit on a demolition bid?

A salvage credit is the estimated value of recoverable metal, applied against the cost of the demolition work. It sits in the bid as a line that reduces the price, which is why getting it wrong in either direction hurts. Too high and the margin disappears. Too low and a competitor takes the job.

The credit isn’t found money. It’s a forecast, and like any forecast in a bid it carries risk that somebody ends up holding.

Deciding who holds it is the first job, and it happens before any arithmetic.

Who owns the scrap?

Whoever the contract says owns it. Standard forms frequently don’t define the term at all, which is where disputes start. There are three workable structures, and the one you choose changes the bid price, who carries market risk, and who pays for hauling. Settle it in writing before work begins.

StructureWhat happens to the metalEffect on the bidWho carries market risk
Owner keeps the scrapOwner sells it or takes the credit directlyDemolition price stays higherThe owner
Contractor keeps the scrapContractor sells it as project revenueBid comes in lowerThe contractor
Proceeds credited against the invoiceRecycler grades and weighs, proceeds applied to the costPriced at cost, credit applied at settlementNobody prices it in advance

The third structure is the one most commercial jobs land on, because it removes the argument. The recycler grades and weighs, the proceeds get applied against the invoice, and everyone sees the same tickets.

It also means the owner isn’t guessing at your margin and you aren’t carrying a price forecast you didn’t want. It’s the structure our demolition scrap service is set up around.

The first two structures both work, they just move the risk. If you keep the metal, you’ve effectively bought a commodity position as part of winning the job. If the owner keeps it, your price goes up and the conversation gets simpler.

Whichever way you go, put it in the contract in plain words. State who keeps the metal, how the value gets credited, and who pays to move it.

How do you estimate salvage value?

Take off recoverable tonnage by material, not theoretical tonnage. Apply a recovery rate you’d actually hit on site rather than a perfect one. Then subtract what it costs to separate, load and haul. What’s left is the number that belongs in the bid, and it’s usually smaller than the first estimate.

That sequence matters, so here it is as steps.

  1. Walk the structure and inventory by material, separating ferrous from non-ferrous. Note where each one sits and how hard it is to reach.
  2. Convert to tonnage using the drawings where you have them and measured sections where you don’t.
  3. Apply a recovery rate. Material behind concrete, buried in slab, or bonded to something else doesn’t all come out.
  4. Cost the work of getting it out, which is labor and machine time that wouldn’t otherwise be in the schedule.
  5. Add container placement and hauling.
  6. Subtract steps 4 and 5 from the value of step 3. That difference is the credit.

The most common failure is stopping at step two. A tonnage figure with no recovery rate and no cost against it isn’t a credit, it’s a hope.

The second most common failure is using last year’s recovery rate on a different kind of building. A steel-framed warehouse and a 1950s masonry structure with embedded steel behave nothing alike, and the rate that worked on one will flatter the other.

Keep the rates you actually achieve. Three or four closed jobs give you better numbers than any published guide, because they reflect your crews and your equipment.

Where the value actually sits

Structural steel and rebar carry the volume. Copper, brass, aluminum and stainless carry the margin per pound.

Both matter, and they behave differently in an estimate. Steel tonnage is predictable and easy to take off from drawings. Non-ferrous is smaller, worth more, and much easier to lose.

That asymmetry is what drives the next decision.

It also shapes where you spend attention during the takeoff. An hour spent nailing down the copper is usually worth more than a day refining the steel tonnage, because the steel number was always going to be roughly right.

Pull the non-ferrous before the structure comes down

Copper and aluminum are non-magnetic, which means once they’re under a pile of steel and masonry nobody is picking them back out efficiently.

Wiring, pipe, fittings, bus bar, HVAC components and window framing all come out cleanly before the machine starts. After teardown, a meaningful share of it is simply gone.

This is a scheduling decision more than a recovery technique. It costs you crew days at the front of the job and returns material at a grade you can actually sell.

Run the numbers on it honestly. On a light structure the strip-out may not pay. On an older commercial building with heavy electrical and plumbing, it usually does.

Access is the variable that decides it. Material you can reach from a floor with hand tools comes out fast. Material behind finishes, in ceiling voids or cast into slab does not, and the labor to chase it eats the difference.

What to lock down before the bid goes in

A credit is only as good as the terms sitting behind it.

  • How the material will be graded, and by whom.
  • Where weighing happens and what documentation comes back.
  • Who supplies containers, and where they can sit on a constrained site.
  • Who hauls, and whether that cost sits with you or the recycler.
  • What happens to material that turns out to be contaminated or unsellable.
  • Whether the recycler will walk the site during bidding rather than after award.

That last one is worth pushing for. A recycler who looks at the structure before you price it will tell you things the drawings won’t, and it costs them an hour.

Ask about container logistics at the same time. On a tight urban site the placement question decides your sequencing, and finding out at mobilization that the box has nowhere to sit is an expensive way to learn it. Roll-off containers and bins come in enough sizes that the constraint is usually access rather than capacity.

What happens when the credit comes in low

This is the question nobody puts in a proposal, and it’s the one that decides whether the job makes money.

Three things move a credit after award. The market moves between bid and settlement. The tonnage doesn’t materialize because recovery was worse than assumed. Or the material grades down because it arrived contaminated.

You can’t control the first. You can control the other two by being conservative at step three and disciplined about separation on site. Grading practice varies between buyers more than most estimators expect.

The structural protection is in how the bid is written. If the credit is a fixed deduction you’ve guaranteed, you’re carrying commodity risk on a job you priced months earlier. If it’s expressed as proceeds applied at settlement, the risk sits where it belongs.

Say which one you’re offering. An owner reading two bids where one guarantees a credit and the other passes through actual proceeds is comparing different products, and the cheaper-looking one isn’t always cheaper.

Spelling that out in the proposal is worth doing even when nobody asked. It signals you’ve priced the job rather than guessed at it, and it gives you somewhere to stand if the market moves against you mid-contract.

Getting a number you can defend

Built from a real takeoff, a realistic recovery rate and costed removal, the number is one you can walk into a scope meeting with. Built from tonnage alone, it isn’t, and the difference tends to surface at settlement rather than at bid.

None of this takes long once you’ve done it twice. The takeoff is work you’re already doing. What changes is applying a recovery rate you believe and pricing the removal instead of assuming it’s free.

We work with demolition contractors across Southern California and we’ll walk a site with you while you’re still pricing it. Current published rates sit on our pricing page, and grading, weighing and documentation work the same on a teardown as on any other load. If you want a demolition scrap salvage credit you can defend, call us to request a project pickup, or send the scope over and we’ll take a look.

Need to sell your scrap?

We buy and process all metals at our South El Monte facility. Competitive payouts, fast turnaround, no hassle. Stop by or reach out to our team today.

Kurt Rexius

Owner
Kurt Rexius is the second-generation owner of P&T Metals in South El Monte, California. With decades of hands-on experience in metal buying, processing, and industrial scrap management, he oversees one of Southern California's few direct mill and foundry suppliers since 1968.